Struct embassy_stm32::usart::BufferedUart

pub struct BufferedUart<'d, T: BasicInstance> { /* private fields */ }

Bidirectional buffered UART

Implementations

impl<'d, T: BasicInstance> BufferedUart<'d, T>

pub fn new( peri: impl Peripheral<P = T> + 'd, _irq: impl Binding<T::Interrupt, InterruptHandler<T>> + 'd, rx: impl Peripheral<P = impl RxPin<T>> + 'd, tx: impl Peripheral<P = impl TxPin<T>> + 'd, tx_buffer: &'d mut [u8], rx_buffer: &'d mut [u8], config: Config ) -> Result<Self, ConfigError>

Create a new bidirectional buffered UART driver

pub fn new_with_rtscts( peri: impl Peripheral<P = T> + 'd, _irq: impl Binding<T::Interrupt, InterruptHandler<T>> + 'd, rx: impl Peripheral<P = impl RxPin<T>> + 'd, tx: impl Peripheral<P = impl TxPin<T>> + 'd, rts: impl Peripheral<P = impl RtsPin<T>> + 'd, cts: impl Peripheral<P = impl CtsPin<T>> + 'd, tx_buffer: &'d mut [u8], rx_buffer: &'d mut [u8], config: Config ) -> Result<Self, ConfigError>

Create a new bidirectional buffered UART driver with request-to-send and clear-to-send pins

pub fn split(self) -> (BufferedUartTx<'d, T>, BufferedUartRx<'d, T>)

Split the driver into a Tx and Rx part (useful for sending to separate tasks)

pub fn set_config(&mut self, config: &Config) -> Result<(), ConfigError>

Reconfigure the driver

Trait Implementations

impl<'d, T: BasicInstance> BufRead for BufferedUart<'d, T>

async fn fill_buf(&mut self) -> Result<&[u8], Self::Error>

Return the contents of the internal buffer, filling it with more data from the inner reader if it is empty.

fn consume(&mut self, amt: usize)

Tell this buffer that amt bytes have been consumed from the buffer, so they should no longer be returned in calls to fill_buf.

impl<'d, T: BasicInstance> ErrorType for BufferedUart<'d, T>

type Error = Error

Error type

impl<'d, T: BasicInstance> ErrorType for BufferedUart<'d, T>

type Error = Error

Error type of all the IO operations on this type.

impl<'d, T: BasicInstance> Read for BufferedUart<'d, T>

fn read(&mut self) -> Result<u8, Error<Self::Error>>

Reads a single word from the serial interface

impl<'d, T: BasicInstance> Read for BufferedUart<'d, T>

fn read(&mut self, buf: &mut [u8]) -> Result<usize, Self::Error>

Read some bytes from this source into the specified buffer, returning how many bytes were read.

fn read_exact( &mut self, buf: &mut [u8] ) -> Result<(), ReadExactError<Self::Error>>

Read the exact number of bytes required to fill buf.

impl<'d, T: BasicInstance> Read for BufferedUart<'d, T>

async fn read(&mut self, buf: &mut [u8]) -> Result<usize, Self::Error>

Read some bytes from this source into the specified buffer, returning how many bytes were read.

async fn read_exact( &mut self, buf: &mut [u8] ) -> Result<(), ReadExactError<Self::Error>>

Read the exact number of bytes required to fill buf.

impl<'d, T: BasicInstance> SetConfig for BufferedUart<'d, T>

type Config = Config

The configuration type used by this driver.

type ConfigError = ConfigError

The error type that can occur if set_config fails.

fn set_config(&mut self, config: &Self::Config) -> Result<(), Self::ConfigError>

Set the configuration of the driver.

impl<'d, T: BasicInstance> Write for BufferedUart<'d, T>

async fn write(&mut self, buf: &[u8]) -> Result<usize, Self::Error>

Write a buffer into this writer, returning how many bytes were written.

async fn flush(&mut self) -> Result<(), Self::Error>

Flush this output stream, ensuring that all intermediately buffered contents reach their destination.

async fn write_all(&mut self, buf: &[u8]) -> Result<(), Self::Error>

Write an entire buffer into this writer.

impl<'d, T: BasicInstance> Write for BufferedUart<'d, T>

fn write(&mut self, buf: &[u8]) -> Result<usize, Self::Error>

Write a buffer into this writer, returning how many bytes were written.

fn flush(&mut self) -> Result<(), Self::Error>

Flush this output stream, blocking until all intermediately buffered contents reach their destination.

fn write_all(&mut self, buf: &[u8]) -> Result<(), Self::Error>

Write an entire buffer into this writer.

fn write_fmt( &mut self, fmt: Arguments<'_> ) -> Result<(), WriteFmtError<Self::Error>>

Write a formatted string into this writer, returning any error encountered.

impl<'d, T: BasicInstance> Write for BufferedUart<'d, T>

fn write(&mut self, char: u8) -> Result<(), Self::Error>

Writes a single word to the serial interface.

fn flush(&mut self) -> Result<(), Self::Error>

Ensures that none of the previously written words are still buffered.

impl<'d, T: BasicInstance> Write<u8> for BufferedUart<'d, T>

type Error = Error

The type of error that can occur when writing

fn bwrite_all(&mut self, buffer: &[u8]) -> Result<(), Self::Error>

Writes a slice, blocking until everything has been written

fn bflush(&mut self) -> Result<(), Self::Error>

Block until the serial interface has sent all buffered words

impl<'d, T: BasicInstance> Read<u8> for BufferedUart<'d, T>

type Error = Error

Read error

fn read(&mut self) -> Result<u8, Error<Self::Error>>

Reads a single word from the serial interface